Deutsch  Deutsch | english  Français
EASYPRO
 
   

TOPAX® MC

 
   

The new multi-channel controller


The TOPAX® MC is Lutz-Jesco GmbH's latest multi-channel controller. Its modular design makes it an adaptable and extremely competent partner for all your measurement and control technology requirements. Whether you need to measure chlorine, the pH value, Redox value, or the pH value four times, the modular design permits any combination.  

The outputs can also be selected freely. For instance, you can actuate dosing pumps via an optocoupler or relay and servomotors via a relay or a 20 mA output.  

The high-resolution 5 inch colour display has a user-friendly operating interface. User-friendliness is rounded off with a simple touch control and multi-lingual intuitive menu navigation.  

Free digital outputs can be configured freely. Irrespective of whether they need to switch following measuring water shortage, measuring value exceedance or undercutting or other possible alarm triggers: the configuration is not subject to any limits.  

You can use the four analogue outputs (0/4 – 20 mA) or the network capability to transfer the measured values to a web browser or a tele-maintenance point. A settable time interval can be used e.g. to issue an automatic reminder for wear-related sensor change. You can use the USB interface to save data (e.g. measured values and parameter settings, alarms, messages etc.) on a USB flash drive.  

    At a glance
  • Modular structure of the inputs and outputs
  • Up to four sensors and additionally up to four temperature sensors
  • Freely-configurable overviews
  • Difference value measurement (e.g. ΔpH)
  • Graphical display of the deviation from the desired setpoint
  • Up to four reference sets can be configured and loaded via a digital input or time control
  • Service entries and sensor change can be saved
  • Limit value control (can be used as a DIN contact for partial load operation in accordance with DIN 19643)
  • 1 – 9 potential-free relay outputs
  • Web server and Modbus protocol via Ethernet
  • Trend Display
  • Large colour touch-display
  • Data is saved on a USB flash drive

For more information please visit our websitewww.topax-mc.de/en

 

More product views

 
 
 
   
 
TOPAX® MC
Housing dimensions (W x H x D)mm 302 x 240 x 107
Voltage supply 100 – 240 V AC, 50/60 Hz
Power consumptionW max. 20
Analogue outputs for remote transmission 4 x 0/4 – 20 mA, working resistance max 500 Ω
Disturbance variable inputmA 0/4 – 20
Interfaces Ethernet TCP/IP or RS485 Modbus RTU (optional)
Protection class IP65
Ambient temperature°C -5 to +45 (no exposure to direct sunlight)
Control characteristic P, PI, PID or PD behaviour, control direction selectable with disturbance variable feed forward, 2-side control selectable
Measuring inputs (depending on version)
Number of measuring inputs up to 4*
Free chlorineAmperometric 3-electrode measuring cell with potentiostat (DMZ3.1)mg/l
0 – 15
(dependant on the measuring cell transconductance)
CS120 excess chlorine measuring cellmg/l 0 – 10
(dependant on the measuring cell transconductance)
Diaphragm-covered measuring cellmg/l 0 – 2 or 0 – 10
(dependant on the measuring cell)
Chlorine dioxideAmperometric 3-electrode measuring cell with potentiostat (DMZ3.1)mg/l 0 – 15
(dependant on the measuring cell transconductance)
CS120 excess chlorine measuring cellmg/l 0 – 10
(dependant on the measuring cell transconductance)
Diaphragm-covered measuring cellmg/l 0 – 2
(dependant on the measuring cell)
Total chlorineDiaphragm-covered measuring cellmg/l 0 – 10
(dependant on the measuring cell)
pH valuepH single-rod measuring cellpH 0 – 14
(dependant on the single-rod measuring chain)
Redox valueRedox single-rod measuring cellmV 0 – 1000 (dependant on the single-rod measuring chain)
Conductivity conductiveConductivity measuring cell (k=1)mS/cm 0 – 2, 0 – 20 or 0 – 100
(Depending on the configuration, corresponds to approx. 0 – 1 % or 0 – 5 % salt content)
TemperaturePt100°C -10 bto +90
5 – 60 (configurable)
Output modules (depending on version)
Servomotor relay 2 x 230 V AC, 5 A (ohmic resistive load)
Potentiometer feedback: 1 – 10
Servomotor 20 mAmA Constant 0/4 – 20 mA output
Servomotor with 20 mA feedback
Relays 2 x 230 V AC, 5 A (ohmic resistive load)
Optocoupler 2 x 80 V DC, 5 mA
         

* An additional temperature sensor can be connected per sensor input.
  Subject to technical changes

   
 
     
 
 

We will be pleased to make you an offer.

Consultant
Saied Ghasemi
Phone: +49 (0)5130 5802-32
Fax: +49 (0)5130 580268
saied.ghasemi(at)lutz-jesco.com

3209