Pump tube Niro for mixing and pumping
Skip image gallery
Explosion protection
ROTOR
*Illustration may differ from the actual product
Available, delivery time: 4 days
Product number:
0151-240
Product information "Pump tube Niro for mixing and pumping"
Description:
The Lutz pumping station (stainless steel) is suitable for corrosive, aqueous to slightly viscous media. Depending on the application, various motors are available which can be combined with the pumping station at any time. This gives you flexibility at all times and saves important resources.
- Also available in special immersion depths from 200 - 2500 mm
- Pumping unit equipped with Lutz original handwheel
- Suitable for mixing and pumping alternative fuels, oils and flammable liquids
Features & benefits
- Also available with Tri-Clamp connection
- Optionally with electric or compressed air drive
- two functions (pumping and mixing) in one device
- No leaks when the pump unit is tilted or moved
- High mixing and conveying capacity for thorough homogenisation
- switching between the pumping and mixing functions takes place without interrupting ongoing operation, which is made possible by a small lever on the handwheel
| Bearings (Material): | Charcoal |
|---|---|
| Certification: | ATEX Directive (ATEX Directive 2014/34/EU) |
| Delivery head (up to max. m wc)*.: | 14,5 |
| Density (up to kg/dm³): | 1,4 |
| Drive shaft (Material): | Stainless steel (1.4571) |
| Explosion protection: | Yes |
| Flow rate (up to max. l/min)*.: | 216 |
| Immersion depth (mm): | 1000 |
| Immersion tube diameter (max. mm): | 41 |
| Impeller (Material): | ETFE (ethylene tetrafluoroethylene copolymer) |
| Liquid temperature (max °C): | 100 |
| Mechanical seal (Material): | Carbon, ceramic, PTFE, HC-4 (2.4610), stainless steel (1.4571) |
| Pump tube material (Material): | Niro (stainless steel) |
| Static seal (Material): | FPM (fluororubber) |
| Thread (inch) outside: | 1 1/4" |
| Type: | MP Niro 50/41-R GLRD |
| Type of impeller / Drive type: | Rotor (axial conveyor wheel) |
| Type of seal: | Mechanical seal: (GLRD) |
| Viscosity (up to max. mPas)*.: | 650 |
When should I use an impeller and when a rotor in a pump tube?
When selecting the appropriate drive type for a Pump tube, the question often arises in practice as to whether an impeller or a rotor should be used. The decision depends largely on the hydraulic requirements of the specific application.
Application 1: High delivery pressure and greater delivery heads required
Requirement
If long hose or pipe runs need to be overcome, the fluid has increased Viscosity or density, or higher overall pressure losses occur, a greater delivery head is required.
Typical influencing factors are:
- Long hose lengths
- Viscous or heavy fluids
- Required pressure build-up in the system
Recommended solution
Impeller (L) = Radial impeller
The impeller is designed for applications where a stable pressure build-up is required. The pump tube thus enables reliable delivery even with increased resistance in the system and ensures a constant delivery capacity under demanding operating conditions.
Application 2: High flow rate with free discharge
Requirement
Where there is a free discharge and no significant Pressure losses in the delivery system, the priority is often to achieve the highest possible flow rate.
Typical influencing factors are:
- Short hose lengths
- Low flow resistance
- Focus on flow rate rather than delivery head
Recommended solution
Rotor (R) = Axial impeller
The rotor is designed for maximum flow rates at minimum back pressure. It is ideal for applications with a free outlet where large flow rates need to be delivered efficiently and economically.
Conclusion:
The choice between an impeller and a rotor depends primarily on the hydraulic requirements of the application. For higher pressure requirements and greater delivery heads, the impeller is the appropriate solution. For free discharge and where high flow rates are required, the rotor is recommended.
Skip product gallery
Accessory Items
Explosion protection
ROTOR
Potential equalisation cable
for flammable liquids
Description:
The potential equalisation cable is used for the electrically conductive connection between the explosion-protected pump and the container and has the function of earthing and potential equalisation.
2 m with fastening clip
Features & advantages
Earthing and potential equalisation function
Explosion protection
ROTOR
Solvent hose set (NBR)
for flammable liquids
Description:
The hose set is suitable for a wide range of commercially available solvents. The hose is electrically conductive so that it can also be used in potentially explosive environments. The set is used to connect to the pumping station or dispensing nozzle.
Also available in special lengths on request
Electrically conductive
Features & advantages
Hose connection: 1 1/4" female thread
Nominal diameter: DN 19 (3/4")
Pre-assembled hose connections
Complies with EU regulations 10/2011 and 1935/2004
Explosion protection
ROTOR
Flow meters TS Type UN10 Ex
for flammable liquids
Description:
The first flow meter with touchscreen display and backlighting impresses with its simple, needs-based display and operability, multilingual interface and compact design. Thanks to the rotating swash plate and a magnet, it enables precise measurement of the volume flow and measures solvents, acids, alkalis, highly flammable liquids, oils and neutral media precisely, quickly and, above all, efficiently. Optionally, the desired quantity can be preselected with the quantity preselection (relay module) so that the pump or system switches off automatically after the selected quantity. This further simplifies and secures the operation of the systems.
Optionally with volume preselection (relay module)
Media examples: Methanol, petrol, isopropanol, paraffin, formic acid, acetic acid, acetone, styrene, xylene, toluene, etc.
Mobile on a drum pump or with nozzle connection or stationary in plant construction
Features & advantages
Measurement according to the wobble disc principle
High measuring accuracy
Variable display orientation
Touchscreen display with self-explanatory, multilingual user interface
Measuring range from 10 l/min- 100 l/min
approved according to ATEX directive 2014/34/EU, category 2
Explosion protection
ROTOR
Brass petrol nozzle
for flammable liquids
Description:
For dispensing and transferring solvents and neutral liquids. The housing and the valve plug of the dispensing nozzle are made of brass and are equipped with a swivel coupling and a protective bracket.The dispensing nozzle is sealed with a PTFE seal.
Connection: external thread G 1 1/4"
Features & advantages
Safe filling or decanting of the respective liquid
Easy to operate
Swivel coupling ensures tightness at high pressure
For pumping in potentially explosive environments
Explosion protection
ROTOR
Universal chemical hose
for flammable liquids
Description:
The hose is suitable for pure chemicals, cosmetics, photographic chemicals, paints and adhesives, detergents and cleaning agents, hygiene products, as well as food and luxury foods. It is FDA and USP Class VI compliant and is electrically conductive so that it can also be used in potentially explosive environments.
Also available in special lengths on request
Nominal width: DN 13 / DN 19 / DN 25 / DN 32 / DN 38 / DN 50
Features & advantages
Operating pressure up to max. 16 bar
Colour coding: "blue/white/blue".
Complies with EU regulations 10/2011 and 1935/2004
Underpressure max 0.9 bar
Explosion protection
ROTOR
FASSADAPTER
for flammable liquids
Description:
The drum adapter is for fastening the pump or pump unit in the drum opening. It prevents the pump from tipping over when the drum is empty.
Materials: PP / ST37 / steel, galvanised / PE
Features & advantages
Stabilisation of the pumping unit
External thread 2", 56 x 4 and 70 x6
Explosion protection
ROTOR
Hose integration
for flammable liquids
Description:
The hose connection ensures a good conductive transition between the hose and the pumping station. The use of conductive hoses is mandatory in potentially explosive atmospheres. The ohmic resistance between the fittings must be less than106 ohms.
For drum and container pumps
Properties & advantages
Made of stainless steel (1.4571)
For mineral oil hoses DN 19 / DN 25 / DN 32
Explosion protection
ROTOR
IBC traverse
for flammable liquids
Description:
The IBC lifting beam is used to safely remove and install the pumping units or the double diaphragm pump.
Suitable for drum pumps, B70 progressive cavity pumps and diaphragm pumps
Includes transport straps for lifting vehicles and tensioning hooks for fixing to the container
Features & advantages
Compatible with all standard IBC containers
Material: stainless steel
Clamping hook: galvanised steel
for drum pumps / B70 version, guide sleeve with Ø 55 mm made of plastic
Explosion protection
ROTOR
Hose set for potentially explosive media
for flammable liquids
Description:
The hose set is suitable for pure chemicals and potentially explosive liquids. The hose is electrically conductive so that it can also be used in potentially explosive environments. The set is used for connection to the pumping station or the dispensing nozzle.
Also available in special lengths on request
Electrically conductive
Features & advantages
Hose connection: 1 1/4" female thread
Nominal diameter: DN 19 (3/4")
Pre-assembled hose connections
Complies with EU regulations 10/2011 and 1935/2004
Explosion protection
ROTOR
Flow meters TS Type LM10 Ex
for flammable liquids
Description:
The first flow meter with touchscreen display and backlighting impresses with its simple, needs-based display and operability, multilingual interface and compact design. Thanks to the rotating swash plate and a magnet, it enables precise measurement of the volume flow and measures solvents and highly flammable liquids, oils and neutral media precisely, quickly and, above all, efficiently. Optionally, the desired volume can be preselected with the volume preselection (relay module) so that the pump or system switches off automatically after the selected volume. This further simplifies and secures the operation of the systems.
Optionally with volume preselection (relay module)
Media examples: Methanol, petrol, isopropanol, paraffin, formic acid, acetic acid, acetone, styrene, xylene, toluene, etc.
Mobile on a drum pump or with nozzle connection or stationary in plant construction
Features & advantages
Measurement according to the wobble disc principle
High measuring accuracy
Variable display orientation
Touchscreen display with self-explanatory, multilingual user interface
Measuring range from 10 l/min- 100 l/min
approved according to ATEX directive 2014/34/EU, category 2
Explosion protection
ROTOR
Flow meters TS Type VA10 Ex
for flammable liquids
Description:
The first flow meter with touchscreen display and backlighting impresses with its simple, needs-based display and operability, multilingual interface and compact design. Thanks to the rotating swash plate and a magnet, it enables precise measurement of the volume flow and measures solvents, acids, alkalis, highly flammable liquids, oils and neutral media precisely, quickly and, above all, efficiently. Optionally, the desired quantity can be preselected with the quantity preselection (relay module) so that the pump or system switches off automatically after the selected quantity. This further simplifies and secures the operation of the systems.
Optionally with volume preselection (relay module)
Media examples: Methanol, petrol, isopropanol, paraffin, formic acid, acetic acid, acetone, styrene, xylene, toluene, etc.
Mobile on a drum pump or with nozzle connection or stationary in plant construction
Features & advantages
Measurement according to the wobble disc principle
High measuring accuracy
Variable display orientation
Touchscreen display with self-explanatory, multilingual user interface
Measuring range from 10 l/min- 100 l/min
approved according to ATEX directive 2014/34/EU, category 2
Explosion protection
ROTOR
Dispensing nozzle Niro
for flammable liquids
Description:
For filling and transferring liquids in the food and pharmaceutical industries as well as flammable and highly flammable liquids. The body and valve plug of the dispensing nozzle are made of stainless steel (1.4571) and are equipped with a protective bracket and a swivel coupling.
EPDM seal available on request at an extra charge
Connection: external thread G 1 1/4"
Features & advantages
For pumping in potentially explosive environments
Simple adjustment of the volume flow
Easy to operate
Safe filling or transferring of the respective liquid
Rotary coupling ensures tightness at high pressure
Explosion protection
ROTOR
Solvent hose
for flammable liquids
Description:
The hose is suitable for a wide range of commercially available solvents. The hose is electrically conductive so that it can also be used in potentially explosive environments.
Also available in special lengths on request
Nominal width: DN 13 / DN 19 / DN 25 / DN 32 / DN 38 / DN 50
Electrically conductive
Features & advantages
Operating pressure up to max. 16 bar
Colour coding: blue
fulfils EU regulations 10/2011 and 1935/2004
Underpressure max 0.9 bar
Skip product gallery
Accessory Items
Explosion protection
ROTOR
Pump tube PP for mixing and pumping
for flammable liquids
Description:
The Lutz pumping station (PP) is suitable for corrosive, aqueous to slightly viscous media. Depending on the application, various motors are available which can be combined with the pumping station at any time. This gives you flexibility at all times and saves important resources.
Also available in special immersion depths from 200 - 2500 mm
Pumping unit equipped with Lutz original handwheel
Suitable for mixing and pumping oils such as rapeseed oil and vegetable oil
Features & advantages
Optionally with electric or compressed air drive
No lubricants and therefore no contamination of the pumped medium by lubricants
Two functions (pumping and mixing) in one device
No leaks if the pumping unit is tilted or moved
High mixing and conveying capacity for thorough homogenisation
switching between the pumping and mixing functions takes place without interrupting ongoing operation, which is made possible by a small lever on the handwheel
Explosion protection
ROTOR
Pump tube PP for mixing and pumping
for flammable liquids
Description:
The drum pump is suitable for corrosive, aqueous to slightly viscous media. Depending on the application, various motors are available which can be combined with the pumping unit at any time. This gives you flexibility at all times and saves important resources.
Also available in special immersion depths from 200 - 2500 mm
Pumping unit equipped with Lutz original handwheel
Suitable for mixing and pumping oils such as rapeseed oil and vegetable oil
Features & advantages
Optionally with electric or compressed air drive
No lubricants and therefore no contamination of the pumped medium by lubricants
Two functions (pumping and mixing) in one device
No leaks if the pumping unit is tilted or moved
High mixing and conveying capacity for thorough homogenisation
switching between the pumping and mixing functions takes place without interrupting ongoing operation, which is made possible by a small lever on the handwheel
Explosion protection
ROTOR
Pump tube PP for mixing and pumping
for flammable liquids
Description:
The Lutz pumping station (PP) is suitable for corrosive, aqueous to slightly viscous media. Depending on the application, various motors are available which can be combined with the pumping station at any time. This gives you flexibility at all times and saves important resources.
Also available in special immersion depths from 200 - 2500 mm
Pumping unit equipped with Lutz original handwheel
Suitable for mixing and pumping oils such as rapeseed oil and vegetable oil
Features & advantages
Optionally with electric or compressed air drive
No lubricants and therefore no contamination of the pumped medium by lubricants
Two functions (pumping and mixing) in one device
No leaks if the pumping unit is tilted or moved
High mixing and conveying capacity for thorough homogenisation
switching between the pumping and mixing functions takes place without interrupting ongoing operation, which is made possible by a small lever on the handwheel